Trident Titanium 24kt Gold PVD Threadless Jewel Pyramid

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Pendant Jewel Star Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Jewelled Lightning Bolt Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Astra Star - 8 Point Star Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Internally Threaded Bee Attachment

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Threadless Trio 5mm Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless 5 Marquise Stone Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Moonstar Attachment w Crystal Attachment

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Internally Threaded 5 Curved Jeweled Prong Set Attachment 0.9mm Thread

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Threadless Mini Trio 4mm Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Jewelled Butterfly Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Internally Threaded Marquise Cut Navel

1.6mm x 10mm / 4mm x 4.8mm

Internally Threaded Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Internally Threaded Square Cut Navel 

1.6mm x 10mm / 4.5mm x 7mm

Internally Threaded Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Threadless Sword Dangle w Oval CZ Attachment

• Sword Size: 10mm
• Crystal Size: 1.5mm x 3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Internally Threaded Mini Bolt Attachment 0.9mm (16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Trio Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Jewel Star Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Titanium 24kt Gold PVD Dangle Pendant Face

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Dagger Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Titanium 24kt Gold PVD Dangle 5 Jeweled Bar

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Internally Threaded 10 Petal Jeweled Flower Attachment 0.9mm (16GA)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Internally Threaded Marquise Attachment 0.9mm (16GA)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Threadless Snake with Crystal Eye Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Jewel Crown Hinged Ring

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Threadless 5 Stone Curved Crown Attachment

•  Size: 3.2mm x 10.3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Triforce Attachment

• Size: 6mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Marquise Stone w CZ Attachment

• Marquise Size: 2.5mm x 5mm
  
• Round Stone Size: 1.5mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Baguette and Round Stones Crown Attachment

• Size: 5mm x 11mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Internally Threaded Round 3 Stones Attachment 0.9mm

• Crystal Sizes: 2mm, 1.5mm 1mm

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Internally Threaded Jewelled 3 Stone Bar Attachment

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Gold PVD Titanium Threadless Nose Labret 1.0mm x 8mm x 2.5mm Crystal - Box 20

Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Internally Threaded  2 Prong Mini Navel

1.6mm x 10mm - 4mm x 6mm Stones

Internally Threaded Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident Titanium 24kt Gold PVD Threadless Ring With 2.5mm Jewel

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Geometric Flower with Crystal Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Star Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Moon Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Chili Bar Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Titanium 24kt Gold PVD Dangle Bolt

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident 24kt Gold PVD Titanium Threadless 9 Curved Prong Set Jeweled Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Marquise with 5 Round Stones Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Crowned Tear 3mm Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Internally Threaded Jewelled 5 Stone Bar Attachment

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)