Trident Threadless Jewelled Ovate Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Curved Jeweled Bar 6.5mm Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Shiva                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. Shiva is a double piercing connected by solid 0.6mm 14kt gold chain. Each stone is 3mm princess cut. The full chain length stretched end to end is 50mm. Crystal to crystal pin chain length is 20mm. Followed by a 2.5mm petit hanging star.

Piece Size: Length / 20mm Piercing to Piercing - Width / 0.6mm - Chain

Pin Gauge: 0.42mm / Length: 4mm

14kt Gold Threadless Attachment - Clara                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. Clara is a pear-shaped gold cast made out of solid 14kt. A 5mm round crystal stone is set below in a unique tension setting.

Piece Size:  Length / 9.8mm -  Width / 5mm

Pin Gauge: 0.42mm / Length: 4mm* 

14kt Gold Threadless Crescent Jewelled Crystal Attachement 

14kt Gold Threadless Triangle Jet w Jewelled Crystal Attachement

Trident Threadless Nipple Cluster 1.6mm x 14mm

Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Threadless Nipple Cluster 3 Balls 1.6mm x 14mm

Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Threadless Nipple Cluster 1.6mm x 14mm

Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

14kt Gold Threadless Lightening Attachment

Gauge: 0.46mm, Length: 5.0mm

14kt Gold Threadless Moon & Opal Attachment

Gauge 0.46mm, Length / 5.0mm

14kt Gold Threadless Disk Attachment

Head Size 3mm / Gauge: 0.46mm / Length: 5.0mm

Trident Threadless Jewel Pyramid Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Ring With 2.5mm Jewel Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Cat                                                                                             

Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.6mm  -  Width / 4.0mm

• Black Crystal Size: 2.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Lotus With Opal Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Snake with Crystal Eye Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Snake with Crystal Eye Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Butterfly Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Jewel Butterfly Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless 5 Stone Curved Crown Attachment

• Size: 3.2mm x 10.3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless 5 Stone Curved Crown Attachment

•  Size: 3.2mm x 10.3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Triforce Attachment

• Size: 6mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Marquise Stone w CZ Attachment

• Marquise Size: 2.5mm x 5mm
  
• Round Stone Size: 1.5mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Marquise Stone w CZ Attachment

• Marquise Size: 2.5mm x 5mm
  
• Round Stones Size: 1.5mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Dangle 2 Round Stones w Baguette Attachment

• Round Stone Size: 2mm
  
• Baguette Size: 1.5mm x 3mm
  
• Overall Size: 12mm
  

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Baguette and Round Stones Crown Attachment

• Size: 5mm x 11mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Baguette and Round Stones Crown Attachment

• Size: 5mm x 11mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Rupee Attachment

• Size: 2.8mm x 6.7mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless 2 Baguette Attachment

• Size: 1.5mm x 3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Nose Labret Rounded Bezel - Box 20

1.0mm x 8mm x 2.35mm Crystal

Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident 24kt Gold PVD Titanium Threadless Nose Labret - Box 20

1.0mm x 8mm x 2.5mm Crystal

Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Nose Labret Rounded Bezel 1.0mm x 8mm x 2.35mm Crystal - Box 20

Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Nose Labret 1.0mm x 8mm x 2.5mm Crystal - Box 20

Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

14kt Gold Threadless - Dangle Baguette                                                                              

Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 8.1mm  -  Width / 2.1mm

• Baguette Crystal Size: 3.0mm x 1.5mm - 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Dagger                                                                                     

Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 6.0mm  -  Width / 4.2mm

• Black Crystal Size: 1.0mm x 4pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Palm Tree w Green Jewel                                                            

Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 5.4mm  -  Width / 4.7mm

• Green Crystal Size: 1.5mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Flat Duck                                                                                 

Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.2mm  -  Width / 3.1

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Wishbone With 1 Jewel CZ                                                            Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 5.9mm  -  Width / 2.8mm

• Blue Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Teddy With Jewel                                                                              Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.3mm  -  Width / 2.4mm

• Crystal Size: 1.1mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Jeweled Crab                                                                                   

Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 6.9mm  -  Width / 3.9mm

• Blue Crystal Size: 0.9mm - 2pcs
• Oval Crystal size: 3.0mm x 2.0mm - 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.