Attachments
Trident Titanium 24kt Gold PVD Dangle Bolt
Trident Titanium 24kt Gold PVD Dangle Bolt
1.8mm Internal Diameter Ring
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident 24kt Gold PVD Titanium Dangle Astra Star - 8 Point Star
Trident 24kt Gold PVD Titanium Dangle Astra Star - 8 Point Star
1.8mm Internal Diameter Ring
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Titanium Dangle Moon
Trident Titanium Dangle Moon
1.8mm Internal Diameter Ring
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Titanium Dangle Jewel Star
Trident Titanium Dangle Jewel Star
1.8mm Internal Diameter Ring
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Titanium Dangle Bolt
Trident Titanium Dangle Bolt
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Internally Threaded Moon with Opal
Trident Internally Threaded Moon with Opal
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Threadless Jewel Oval Stone with Round Stone
Trident Threadless Jewel Oval Stone with Round Stone
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
White 14kt Gold Threadless Opal
White 14kt Gold Threadless Opal Made out of solid 14kt Gold & implant grade steel pin. 4mm white fire cultured opal embedded in a solid 14kt gold cast.
Piece Size: Length / 4mm - Width / 4mm
Pin Size: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Trident Threadless 9 Curved Prong Set Jeweled
24kt Gold PVD Trident Threadless 9 Curved Prong Set Jeweled
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Threadless Triplet Jeweled Spike
Trident Threadless Triplet Jeweled Spike
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
White Gold 14kt Threadless Prong Set
White Gold 14kt Threadless Prong Set 3mm Stone Made out of solid 14kt Gold & implant grade steel pin.
Piece Size: Length / 3mm - Width / 3mm
Pin Size: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
White 14kt Gold Threadless Jewel Sword
White 14kt Gold Threadless Jewel Sword Made out of solid 14kt Gold & implant grade steel pin. Tip to tip the beautify detailed sword is 9.1mm long and 4.3mm wide.
Piece Size: Length / 9.1mm - Width / 4.3mm
Pin Size: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
White 14kt Gold Threadless Trio
Pin Size: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
White 14kt Gold Threadless Moon & Opal
White 14kt Gold Threadless Moon & Opal Made out of solid 14kt Gold & implant grade steel pin. Jeweled with 1.5mm white fire cultured opal.
Piece Size: Length / 3.3mm - Width / 3mm
Pin Size: 0.42mm / Length: 4mm*
White 14kt Gold Threadless Lunar
White 14kt Gold Threadless Lunar Made out of solid 14kt Gold & implant grade steel pin. The 3 balls aside the crescent are 1mm each.
Piece Size: Length / 3.4mm - Width / 3.5mm
Pin Size: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
White Gold 14kt Threadless Jeweled Bezel
White Gold 14kt Threadless Jeweled Bezel Made out of solid 14kt Gold & implant grade steel pin.
Piece Size: Length / 3mm - Width / 3mm
Pin Size: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Threadless Marquise with 5 Round Stones
Trident 24kt Gold PVD Threadless Marquise with 5 Round Stones
Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Trio Diamond Shape Fan
Trident Threadless Trio Diamond Shape Fan Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Threadless Marquise Trio - Aqua, Orange, Yellow
Trident Threadless Marquise Trio Aqua, Orange, Yellow
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Marquise Trio - Green, Blue, Clear
Trident Threadless Marquise Trio Green, Blue, Clear
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Marquise Trio - Aqua, Clear, Red
Trident Threadless Marquise Trio Aqua, Clear, Red
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Internally Threaded Marquis with 4 Stones Prong Set
Trident Internally Threaded Marquis with 4 Stones Prong Set Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Titanium Threadless Crescent Moon
Trident Titanium Threadless Crescent Moon
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Threadless Attachment Crowned Tear
Trident 24kt Gold PVD Threadless Attachment Crowned Tear 3mm
Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Marquise Trio - Red, Clear, Purple
Trident Threadless Marquise Trio Red, Clear, Purple
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident 24kt Gold PVD Jeweled 5 Stone Bar Attachment
Gold PVD Trident Titanium 0.9mm Internally Threaded Jeweled 5 Stone Bar Attachment
Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Titanium Threadless 3 Baguette Stone
Trident Titanium Threadless 3 Baguette Stone Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Princess Cut Jeweled Trio Attachment
Threadless Princess Cut Jeweled Trio Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 3mm Jewel Ovate w Jewel Dangle
Trident Threadless 3mm Jewel Ovate w Jewel Dangle
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Titanium Threadless Jeweled Lightening Bolt
Trident Titanium Threadless Jeweled Lightening Bolt
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Jeweled Pyrus Attachment
Trident Threadless Jeweled Attachment - Pyrus
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Jeweled Cross Attachment
Threadless Jeweled Cross Attachment 6mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 9 Stone Prong Set Attachment
Threadless 9 Stone Prong Set Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Threadless Jeweled Attachment - Tia
Trident Threadless Jeweled Attachment - Tia
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Cluster Jewel Attachment - Tear Cluster
Trident Threadless Cluster Jewel Attachment - Tear Cluster
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 4mm Jeweled Dangle Bar Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Bar Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Cluster Jewel Attachment - 2 Jeweled Beaded Tear
Trident Threadless Cluster Jewel Attachment - 2 Jeweled Beaded Tear
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Cluster Jewel Attachment - Beaded Ovate
Trident Threadless Cluster Jewel Attachment - Beaded Ovate
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Threadless 4mm Jeweled Dangle Bezel Attachment
Trident Threadless 4mm Jeweled Dangle 3mm Bezel Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 6 Petal Flower Jeweled Attachment
Threadless 6 Petal Flower Jeweled Attachment 6mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Threadless 4mm Jeweled Dangle Ball Trio Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Ball Trio Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Threadless 4mm Jeweled Dangle Lightening Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Lightening Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Threadless 4mm Jeweled Dangle Moon Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Moon Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Threadless 4mm Jeweled Dangle Cross Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Cross Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Trident Internally Threaded Jeweled Paw Cluster Attachment
Trident Titanium Internally Threaded Jeweled Paw Cluster Attachment 16GA
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
14kt Gold Threadless Attachment - Lola
14kt Gold Threadless Attachment - Lola Made out of Nickle free solid 14kt Gold & implant grade steel pin. Lola is made of 4 marquise crystals. Each stone is 3.0mm by 1.6mm. The above ball is 1.9mm made of solid gold.
Piece Size: Length / 9.8mm - Width / 5.5mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Lulu
14kt Gold Threadless Attachment - Lulu Made out of Nickle free solid 14kt Gold & implant grade steel pin. Lulu is made of 4 marquise crystals. Each stone is 3.0mm by 1.6mm. The above ball is 1.3mm made of solid gold.
Piece Size: Length / 9.8mm - Width / 5.5mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.